Adding A Belt Hole

I would prefer to introduce you to one in all my all time favourite style instruments… the Leather Hole puncher ! Maybe you lost or gained some weight; possibly you discovered the right belt at a thrift retailer, but it surely's a not the proper measurement; perhaps you want a Hole between two of the already existing holes-regardless of the subject is, this tutorial will present you learn how to add nice spherical belt holes. Use a bit of scrap Leather beneath the belt, so that you just're not hammering the punch right into the anvil. The new holes look slightly more ragged around the edges, but using the belt will help to clean them down.
Remember, the extra eight-eleven″ in. will the be additional tail finish of your belt that slips away in the belt loops of your pants when you put on it. You don't want this to be too lengthy or too quick; too lengthy, and the belt will look too large, but too brief, and the belt will look too small for you! Upon getting your piece shaped how you like it, go forward and top-stitch your cloth Make sure your bobbin as well as your spool of thread on top are full sufficient you could stitch all around the border of your belt in one go!



Nicely except its an expensive belt and you want to retain the integrity of the made Hole. You could additionally get one of many Leather punch from ebay and use it for different future Leather Hole making purposes. In the event you resolve to make use of a drill make sure to maintain the belt down tight and secure, it's going to spin round real quick in case you do not. I used to do use a Leather punch as a result of my belts have been all the time half a notch too large or half a notch too small.
Apply on the very end (that you will lower off later) to get a feel for the way the drill and Leather interact. Looks just like the Tandy Leather website retailer has gone kaput, the belt clean and belt preserve hyperlinks don't work any longer. Tom, Unfortunately it appears to be like like this printed across the identical time Tandy did a value improve on the belt clean. Tom: $7 balm + $1 maintain + $2 buckle + $19 belt clean = $29 - $10 from code = $19. I have already got Sno Seal at dwelling and wish to keep away from buying the Leather Balm if it does the same factor.

Work the Leather up and down the outlet to try to stretch it out a bit of as it will not be the exact same measurement as the opposite holes that had been punched initially. Subsequent we have to eliminate the excess Leather at the finish so we do not appear to be we've got a tail hanging out on the entrance of our pants. Again I marked the place I felt applicable with a sharpie and simply used my household scissors to cut the Leather. Ensure that it's trimmed and good, and then top-stitch it in the same approach that you simply did your belt piece.
Regardless of which of the methods under you go for, 90% of your success can be determined not by how the hole will get there, but by where you put it in the first place. Or, in the event you're loopy obsessive (I'm), you can also make a little template with some painters tape. There's not much to it: Mark your spot, and place your belt on some scrap wooden. Possibility #three: The Leather Hole Punch This designated software is by far essentially the most splendid possibility.
One does not simply whip up a high quality Leather belt that can support instrument bag's or holsters by following this method. So no you failed and took good Leather and wasted it. An ideal belt is 1/4 inch thick from two high grain straps bonded and sewn, beveled and burnished colored with dye and then sealed. I purchased 5 belt blanks, 5 belt retains, completely different dyes and balms, burnisher, and Leather edging instrument all from Amazon and Tandy. To make this challenge even more genuine I went to the Tanner Goods website and bought their commonplace buckles at a value $8.00 each in silver, brass, copper and black.

You need to attempt on the belt and get an thought for the way a lot you will have to carry the belt in, one extra Hole is all i wanted for this one. Some belts have screws close make hole in belt to the buckle which you can remove and relocate to shrink the belt. I don't have a Leather Hole punch, so I simply used a nail that I had and punched the hole a couple of instances.
Take a tape measure and determine the width of your hips, or wherever your belt will be sitting whenever you wear it. No matter quantity you give you, add about 8-10″ in. This needs to be the length of the fabric to your belt altogether! This cloth has a backing and is thick enough with only one layer, so I only wanted to cut one piece for the belt. With this Leather fabric, I wanted to trim the perimeters so the perimeters lined up properly with the squares of the basketwoven strips. You must also take the time to double-verify that your strip of fabric on your belt will match now that it is trimmed down.

Leave a Reply

Your email address will not be published. Required fields are marked *